Multiband diplexer DC-960&1500-2100/2600 MHz 4.3-10 female DC port 1 to 3 product photo Front View L
For a larger view click on the picture.

Multiband diplexer DC-960&1500-2100/2600 MHz 4.3-10 female DC port 1 to 3

572668
Compare

SPINNER Combining Units for best radio frequency networks performance

Combining units are essential components in radio frequency networks, used to merge signals from multiple sources or split signals into multiple paths while maintaining signal integrity. All combiners work in bi-directional mode and can therefore be used to combine and split the transmitted and received signals.

The Multiband diplexer 300-2100/2600 MHz 4.3-10 female DC port 2 to 3 guarantees excellent, lossless mobile communication quality for use in in-building distributed antenna systems (DAS) or on mobile communication base stations outdoors.

A multiband combiner is designed to combine signals from multiple frequency bands into a single output. This enables the effective use of antenna systems by reducing the number of antennas needed, which is crucial in dense network environments or where space is at a premium. Multiband combiners facilitate the operation of different frequency bands on a single feedline, optimizing both system efficiency and performance by simplifying infrastructure and minimizing hardware requirements.

They are typically used in:

  • Co-Located Base Stations: In scenarios where multiple base stations are located close to each other (co-location), Multiband Combiners allow them to share a single antenna system.
  • Distributed Antenna Systems (DAS): For in-building coverage or large indoor spaces, Multiband Combiners combine signals from various operators into a unified signal for distribution.
  • Shared Infrastructure: Multiband Combiners enable cost-effective sharing of resources among different wireless service providers.

Critical characteristics are:

  • Isolation: High isolation between input ports prevents interference between combined signals.
  • Low Insertion Loss: Minimizing signal loss during combining ensures optimal network performance.
  • Wide Bandwidth Coverage: Multiband Combiners should support a broad range of frequencies to accommodate various wireless technologies.
  • Compact Design: Space efficiency is crucial, especially in indoor installations.
  • Robust Construction: Outdoor versions must withstand environmental conditions (temperature, humidity).

Benefits are:

  • Scalability: Multiband Combiners can adapt to changing network requirements without major modifications.
  • Cost-Effectiveness: Shared infrastructure reduces costs for operators and building owners.
  • Efficient spectrum utilization: by combining bands, multiband combiners optimize spectrum usage.
  • Quick deployment: easy installation speeds up network rollout.

A diplexer is a device that separates or combines signals from two different frequency bands. These defined frequency bands can sometimes be quite wide, then we’re talking about ultra broadband devices. The diplexer allows these signals to share a common feeder line or antenna while maintaining isolation between them.

Outstanding RF characteristics, best possible passive intermodulation and VSWR

The Multiband diplexer 300-2100/2600 MHz 4.3-10 female DC port 2 to 3 enables you to transmit high-frequency signals reliably and flawlessly with optimum protection of your sensitive equipment in a power range up to Port 1: 500 W, Port 2: 300 W with maximum passive intermodulation (IM3) of -160 dBc.

The protection class is IP 67.

The port path designation regarding main line and probe is as follows: Port 1, 2: input, Port 3: output

It supports the use of the following frequency bands : 300, 700, 800, 900, 1800, 2100, 2600

The 4.3-10 connector system was designed to meet the latest requirements in mobile communication in terms of size, robustness, performance, and other parameters. Its small footprint supports the use of smaller components, mitigates risks if equipment is assembled without due care, and delivers outstanding electrical performance.

RF characteristics

Number of interfaces:
3
Interface type:
4.3-10 female (50 Ω) per IEC 61169-54
Port / path designation:
Port 1, 2: input
Port 3: output
Interface direction:
straight
Version:
single
Input : output ratio:
2 : 1
Combiner type:
Multiband combiners
Standard:
Mobile communication
Frequency range:
Port 1: DC to 960 MHz
Port 1: 1427 to 2170 MHz
Port 2: 2496 to 2690 MHz
Frequency band:
1800, 2600, 1500, 300, 400, 700, 2100, 800, 900
Average power rating:
Port 1: 600 W
Port 2: 100 W
Surge Protection:
N/A
VSWR, max.:
1.25
Insertion loss max.:
Port 1, 2 → Port 3: 0.3 dB
Isolation, min.:
Port 1 ↔ Port 2: 50 dB
Passive intermodulation (IM3), max.:
-160 dBc @ 700 to 2690 MHz
DC-Bypass:
Port 1 ↔ Port 3 (bidirectional)
(max. 1A per input max. 60V DC (AISG Standard, 2.0, § 6.4))

Mechanical characteristics

Colour:
grey
Degree of protection:
IP 67
Weight, approx.:
2.5 kg
Length:
160.0 mm
Width:
116.0 mm
Height:
40.0 mm
Dimensions remark:
(Excluding brackets and connectors)

Environmental conditions

Environmental conditions:
ETSI EN 300019-1-1 Class 1.2
ETSI EN 300019-1-2 Class 2.3
ETSI EN 300019-1-4 Class 4.1E
Operating temperature:
-40 to +55 °C
Relative humidity, max.:
95% (non-condensing)

Scope of delivery & accessories

Mounting accessoires:
part of delivery

Further remarks

Customs tariff number:
85177900

Downloads

572668-DS.pdf

Product data sheet – 572668 – 572668-DS.pdf

572668-MS.vex

Model – 572668 – iBwave VEX file – 572668-MS.vex

REACH_Mobile_Communication_10123443-TD.pdf

Technical document – 572668 – REACH-Certificate for Mobile Communication Products – REACH_Mobile_Communication_10123443-TD.pdf

RoHS_Mobile_Communication_10123425-TD.pdf

Technical document – 572668 – RoHS-Certificate for Mobile Communication Products – RoHS_Mobile_Communication_10123425-TD.pdf